Paint Racing Stripes on a Car

27/10/2018

3726

Paint Racing Stripes on a Car

Have you ever noticed that many expensive, high-end car models are now painted yellow, orange, and other outrageous colors? The owners of such cars probably want them to stand out from the rest of the vehicles in parking lots. However, there are other, better solutions to making your car an attention magnet without painting it to look like a taxi. One of the most popular—and probably simplest—ways to customize your automobile is to add a second color to your original paint job. To get a two-color scheme for your car, why not try adding racing stripes? The process is quite simple, and with the proper equipment, you too can add any type of racing stripes to your car.

Decide which type of racing stripes you want for your car. Racing stripes can be thick or thin bands. They can run across the hood or along the sides of your car. You can paint them in one shade or use two different colors. To find a suitable design for your vehicle, look at different photos of cars. You can also search for inspiration on the Internet by entering “car racing stripes” into your search engine. You will be able to browse through thousands of racing stripe styles.
Choose your work area. Park your car in a well-ventilated, shaded area where the temperature does not exceed 90 degrees F. It is also recommended that you work where there is good lighting and no wind.
Prep your car for painting. Thoroughly wash your vehicle with warm soapy water, ensuring that no dust or dirt remains on the shell. Rinse off the detergent with clean water. Wipe the car down with a soft, clean rag. If you can find one, use a prep wipe, also known as a degreaser, on the parts of the car where you want to place the racing stripes. This will remove any residual grease or wax on your work surface. Lay out your desired stripes using masking or painter’s tape. Use a tape measure or ruler to mark where you need to stick the tape to ensure that the lines are correctly and evenly spaced. Spread a thin coat of primer on the surface between the outlines marked by the tape. Let it dry completely. With a sheet of fine-grit sandpaper, preferably 1200 to 1500 grit, sand the parts that need to be painted. Take care not to scratch off the painter’s tape covering the other sections that you do not want painted. Cover the entire shell of your car with newspaper and tape. This will protect the rest of the surfaces from any overspray.
Begin spraying the stripe or stripes. Load the paint primer into the spray gun. Start spraying on the area covered by the newspaper. Once you have a constant stream going, begin moving your sprayer across the area to be painted. Do not start or stop spraying within the taped surface. This will cause that area to be painted unevenly. Wait for about 30 minutes or until the primer dries completely. Apply the first coat of color paint using exactly the same technique you used with the primer. To achieve an opaque finish, you will need to apply at least three coats of paint. Do not forget to wait ten to fifteen minutes between coats. Inspect your work after the final coat. Remove the tape a few minutes afterward.

Wait for several days for the paint to cure before removing the edges of your new paint job. You can use a rubbing compound or 1500-grit sandpaper. Consider applying a clear coat to the entire shell of your car before washing and waxing it.

Paint Racing Stripes on a Car

Paint Racing Stripes on a Car : Multi-thousand tips to make your life easier.

Decide which type of racing stripes you want for your car. Racing stripes can be thick or thin bands. They can run across the hood or along the sides of your car. You can paint them in one shade or use two different colors. To find a suitable design for your vehicle, look at different photos of cars. You can also search for inspiration on the Internet by entering “car racing stripes” into your search engine. You will be able to browse through thousands of racing stripe styles.
Choose your work area. Park your car in a well-ventilated, shaded area where the temperature does not exceed 90 degrees F. It is also recommended that you work where there is good lighting and no wind.
Prep your car for painting. Thoroughly wash your vehicle with warm soapy water, ensuring that no dust or dirt remains on the shell. Rinse off the detergent with clean water. Wipe the car down with a soft, clean rag. If you can find one, use a prep wipe, also known as a degreaser, on the parts of the car where you want to place the racing stripes. This will remove any residual grease or wax on your work surface. Lay out your desired stripes using masking or painter’s tape. Use a tape measure or ruler to mark where you need to stick the tape to ensure that the lines are correctly and evenly spaced. Spread a thin coat of primer on the surface between the outlines marked by the tape. Let it dry completely. With a sheet of fine-grit sandpaper, preferably 1200 to 1500 grit, sand the parts that need to be painted. Take care not to scratch off the painter’s tape covering the other sections that you do not want painted. Cover the entire shell of your car with newspaper and tape. This will protect the rest of the surfaces from any overspray.
Begin spraying the stripe or stripes. Load the paint primer into the spray gun. Start spraying on the area covered by the newspaper. Once you have a constant stream going, begin moving your sprayer across the area to be painted. Do not start or stop spraying within the taped surface. This will cause that area to be painted unevenly. Wait for about 30 minutes or until the primer dries completely. Apply the first coat of color paint using exactly the same technique you used with the primer. To achieve an opaque finish, you will need to apply at least three coats of paint. Do not forget to wait ten to fifteen minutes between coats. Inspect your work after the final coat. Remove the tape a few minutes afterward.