Advertisements and information about an event, project, or activity are often printed on banners. One way to display banners is to put them in stand-alone frames. If you use banners often, you can save money by placing them in reusable frames. This way, all you need to do is remove the old banner and replace it with a new one. There is no need to buy a new frame each time.
Instead of buying frames, you can make your own banner frame using PVC pipes. It doesn’t take long to make, and the materials you need are readily available at your local hardware store.
Materials
For this PVC banner frame project, you will need the following materials:
- 1 PVC pipe (¾ inch)
- 8 “T” connectors (¾ inch)
- 2 elbow joints (¾ inch)
- PVC cutter or hacksaw
- Tape measure or yardstick
- Adhesive for PVC
Directions
- Find out how big your banner is. Use your tape measure or yardstick to get the exact length and width of your banner. Add ½ inch to each side of these measurements. You need this extra ½ inch so you can fasten the banner to your completed PVC banner frame later.
- Prepare the PVC pipes. Use the measurements you took earlier (with the additional ½ inch added to the dimensions). Cut the pipe to these measurements with your PVC cutter or hacksaw. Also prepare two extra pieces of 2-foot-long PVC pipe and eight pieces of 1-foot-long PVC pipe.
- Attach the “T” connectors. Take four of the 1-foot PVC pipes. Place four of the “T” connectors in the center of these 1-foot pipes. Make sure that the empty connector faces the side of the PVC pipe.
- Attach PVC pipes to the empty connectors. Take a 1-foot pipe and slide it securely into one empty connector. Do the same for the other empty connector. Using a “T” connector, join the two poles. Repeat this procedure for the other poles. Make sure that the “T” connector faces upward.
- Fasten the longer poles. Take one 2-foot pole and attach it to one upward-facing connector. Do the same for the other 2-foot pole. Attach a “T” connector to each pole.
- Get the PVC pipes that were cut according to the length of the banner. Insert these pipes into the holes on the sides of the poles.
- Get the PVC pipes that were cut according to the width of the banner. Insert these pipes into the top holes. Attach elbow joints at the top.
- Connect the remaining PVC pipes by inserting them into the holes.
- Apply adhesive to the connectors. The adhesive strengthens and holds the frame together. Now you can hang your banner in your PVC banner frame using twine, rope, or other types of tying implements.
Reminders: If the PVC banner frame is to be displayed outdoors or in a windy location, make sure to place bricks or other heavy objects at the base of the stand to keep the frame in place.
PVC is inexpensive, sturdy, and weatherproof. Making a PVC banner frame is an easy DIY project. If you often use banners for your business or work, the PVC frame above can be used over and over again.
Make a PVC Banner Frame
Make a PVC Banner Frame : Multi-thousand tips to make your life easier.
Advertisements and information about an event, project, or activity are often printed on banners. One way to display banners is to put them in stand-alone frames. If you use banners often, you can save money by placing them in reusable frames. This way, all you need to do is remove the old banner and replace it with a new one. There is no need to buy a new frame each time.
Instead of buying frames, you can make your own banner frame using PVC pipes. It doesn’t take long to make, and the materials you need are readily available at your local hardware store.
Materials
For this PVC banner frame project, you will need the following materials:
- 1 PVC pipe (¾ inch)
- 8 “T” connectors (¾ inch)
- 2 elbow joints (¾ inch)
- PVC cutter or hacksaw
- Tape measure or yardstick
- Adhesive for PVC
Directions
- Find out how big your banner is. Use your tape measure or yardstick to get the exact length and width of your banner. Add ½ inch to each side of these measurements. You need this extra ½ inch so you can fasten the banner to your completed PVC banner frame later.
- Prepare the PVC pipes. Use the measurements you took earlier (with the additional ½ inch added to the dimensions). Cut the pipe to these measurements with your PVC cutter or hacksaw. Also prepare two extra pieces of 2-foot-long PVC pipe and eight pieces of 1-foot-long PVC pipe.
- Attach the “T” connectors. Take four of the 1-foot PVC pipes. Place four of the “T” connectors in the center of these 1-foot pipes. Make sure that the empty connector faces the side of the PVC pipe.
- Attach PVC pipes to the empty connectors. Take a 1-foot pipe and slide it securely into one empty connector. Do the same for the other empty connector. Using a “T” connector, join the two poles. Repeat this procedure for the other poles. Make sure that the “T” connector faces upward.
- Fasten the longer poles. Take one 2-foot pole and attach it to one upward-facing connector. Do the same for the other 2-foot pole. Attach a “T” connector to each pole.
- Get the PVC pipes that were cut according to the length of the banner. Insert these pipes into the holes on the sides of the poles.
- Get the PVC pipes that were cut according to the width of the banner. Insert these pipes into the top holes. Attach elbow joints at the top.
- Connect the remaining PVC pipes by inserting them into the holes.
- Apply adhesive to the connectors. The adhesive strengthens and holds the frame together. Now you can hang your banner in your PVC banner frame using twine, rope, or other types of tying implements.
Reminders: If the PVC banner frame is to be displayed outdoors or in a windy location, make sure to place bricks or other heavy objects at the base of the stand to keep the frame in place.
PVC is inexpensive, sturdy, and weatherproof. Making a PVC banner frame is an easy DIY project. If you often use banners for your business or work, the PVC frame above can be used over and over again.